ASSALLAMUALAIKUM WR WB Selamat malam para blogger semoga di hari ini kalian semua sehat walafiat Kali ini saya akan memperlihatkan bagaimana cara hack @wifi.id dengan cara mengkloning macc address kita dengan macc address korban menggunakan terminal di kali linux.
![Cara Hack Wifi Dengan Wireshark Kali Linux Cara Hack Wifi Dengan Wireshark Kali Linux](/uploads/1/2/5/6/125626124/476816856.jpg)
Share. LinkedIn. Facebook. Twitter 2 Wireshark is the world’s foremost network protocol analyzer. It lets you see what’s happening on your network at a microscopic level. It is the de facto (and often de jure) standard across many industries and educational institutions.
This tutorial can be an angel and also devil in the same time, it depends to you who use this tutorial for which purposeme as a writer of this tutorial just hope that all of you can use it in the right way, because I believe that no one from you want your password sniffed by someone out there so don’t do that to others too Disclaimer – Our tutorials are designed to aid aspiring pen testers/security enthusiasts in learning new skills, we only recommend that you test this tutorial on a system that belongs to YOU. We do not accept responsibility for anyone who thinks it’s a good idea to try to use this to attempt to hack systems that do not belong to you Requirements: 1.
![Cara Hack Wifi Dengan Wireshark Kali Linux Cara Hack Wifi Dengan Wireshark Kali Linux](/uploads/1/2/5/6/125626124/270396449.jpg)
Wireshark Network Analyzer (wireshark.org) 2. Network Card (Wi-Fi Card, LAN Card, etc) fyi: for wi-fi it should support promiscious mode Step 1: Start Wireshark and capture traffic In Kali Linux you can start Wireshark by going to Application Kali Linux Top 10 Security Tools Wireshark In Wireshark go to Capture Interface and tick the interface that applies to you. In my case, I am using a Wireless USB card, so I’ve selected wlan0.
Step 2: Filter captured traffic for POST data At this point Wireshark is listening to all network traffic and capturing them. I opened a browser and signed in a website using my username and password.
When the authentication process was complete and I was logged in, I went back and stopped the capture in Wireshark. When wee type in your username, password and press the Login button, it generates a a POST method (in short – you’re sending data to the remote server).
To filter all traffic and locate POST data, type in the following in the filter section http.request.method “POST” See screenshot below. It is showing 1 POST event.
Kali Linux Wash is a tool to find WPS enabled routers in your area. A lot of routers support Wifi Protected Setup (WPS) and it’s likely enabled by default by your internet service provider or by the router manufacturer. Like UPnP, it is an insecure feature that makes your wireless network more vulnerable to certain attacks. Pixie dust vulnerable routers with WPS turned on for example, can be cracked in a matter of seconds. Make sure to disable it in your router settings to avoid attacks like these. In this tutorial we’re going to use Kali Linux Wash to scan for WPS enabled networks in the area.
Wash can also be used to determine whether an access point is locked or not. A lot of routers tend to lock WPS when the PIN is being brute forced with a tool like Reaver, usually after 5 or 6 attempts. Unlocking WPS has to be done manually in the administrator interface of the router. It might be needless to say but Wifi networks with WPS disabled are less likely to be the target of a hacker because the easiest and fastest ways of hacking the wireless network are ruled out.
Without the possibility of WPS related attacks the attacker is left to more time consuming ways to hack your Wifi network, like capturing handshakes and brute force these or more advanced ways. Turning WPS off in combination with a strong wireless network password will keep out most attackers. Let’s put the wifi interface in monitoring mode using: airmon-ng start wlan0 update For anyone getting the following error in Kali Linux 2.0: X ERROR: Failed to open ‘wlan0mon’ for capturing try this as a solution: 1. Put the device in Monitor mode Airmon-ng start wlan0 2. A monitoring interface will be started on wlan0mon 3.
Use iwconfig to check if the interface MODE is in managed mode, if so then change it to monitor instead of managed with the following commands: ifconfig wlan0mon down iwconfig wlan0mon mode monitor ifconfig wlan0mon up 4. Iwconfig check if the mode is monitoring mode now 8. Airodump-ng wlan0mon If necessary kill the mentioned processes which could disturb the scanning process using the following command: kill pid Use the following command to start Kali Linux Wash: wash -I monitoring interface Wash gives you an overview of wireless networks in range and tells you if WPS is locked or not. Press control + C to exit Wash and return to your command line. Kali Linux Wash video tutorial Thanks for watching and it would be awesome if you subscribed to my:) If you’re interested in learning more about WiFi hacking, Wireshark, hacking tools and wireless in general, you can follow any of these online courses: Online Hacking Courses Learn Wi-fi Hacking/Penetration Testing From Scratch This course contains 50 Videos to learn practical attacks to test the security of Wi-fi and wired networks from scratch using Linux. ARP spoofing & Man In The Middle Attacks Execution & Detection Learn practical attacks to test the security of clients connected to a network and how to protect against these attacks.